Just How to Install a Bathtub Yourself: Removing as well as Replacing.
Just How to Install a Bathtub Yourself: Removing as well as Replacing.
Blog Article
The article in the next paragraphs on the subject of How to Install a Bathtub is truly intriguing. Check it out yourself and figure out what you think of it.
Setting up a tub isn't precisely brain surgery, yet it does need strong plumbing, woodworking, and also sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a reasonably difficult job. If the old bathtub is easily obtainable, the project can relocate speedily; if you have to open a wall to eliminate the old tub as well as place the new tub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly require a helper to move out the old tub as well as set in the new one. See to it you have actually qualified yourself for the work and fit trying it. As opposed to employing a specialist to take control of a halfway-completed job, it is better to think about using one prior to you start. Opportunities are you might need an expert plumber to make tube connections.
This short article will aid you set up a new bathtub in your washroom if you have actually currently gotten a new tub and do not require to alter the plan of your previous supply of water pipelines.
Your tools and also product checklist should comprise the following:
Planning for the Installment
First of all, the supporting frame provided with the bathroom ought to be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now prepare to be suited its final placement.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic as a result of the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the spirit level reads level.
To set up taps, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other tap.
Turn on the water system as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and the regular outlet for leaks.
Finally, deal with the bathroom paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub ought to wait up until the tub has been utilized a minimum of when as this will certainly resolve it right into its last position.
Fitting New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin guaranteeing that the washers are in area in between the faucet and also the sink. Protect the tap in place with the producer provided backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, resulting in complications with dampness and also feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched newspaper or soft rope. Remember to constantly fill up the bathtub with water prior to securing, to allow for the movement experienced when the bathtub is in use. The sealer can break relatively early if you do not take into account this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is a good idea to fit the tiles utilizing waterproof or water-proof sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I figured sharing that topic was worth the trouble. Enjoyed reading our blog posting? Please share it. Help other people check it out. Thank you so much for going through it.
Click For More Information Report this page